![]() The subscription LED on the base stops flashing and is solid green. ![]() If the base is in subscription mode and you want to stop the base from searching for a headset, press the subscription button again or place the headset in the charging cradle. NOTE If the subscription process times out after 2 minutes or if the subscription process fails, try to re-subscribe the headset again. When the base subscription LED turns solid green and the headset LED turns off, the headset and base are subscribed to one another. ![]() Press and hold the Volume up button on the headset for 4 seconds until the headset LED flashes red and green.The subscription LED on the display panel flashes red and green. With your system idle and your headset undocked, double-click the Subscription button on the back of the base.The base subscription LED will flash during the subscription process and becomes solid green when the new subscription is established. With your system idle, docking a headset will automatically subscribe it to the base, making it the primary headset. However, if you wish to use a new headset or need to restore a subscription to your current headset, the units can be subscribed to each other by the following two methods. The headset and base that came in the box are subscribed (connected) to each other. Most other phones use default configuration A. IMPORTANT Cisco phones use configuration D on the bottom of the base. IMPORTANT Use configuration A on the bottom of the base, which works for most phones including Cisco phones.ĭ Desk phone + HL10 lifter (sold separately) In this configuration, manually remove the handset on your desk phone and press the call control button on the headset to answer or end calls.Ĭ Desk phone + EHS cable (sold separately) NOTE Use this setup if you are not using the HL10 lifter or EHS cable and your desk phone does not have a dedicated headset port. Finally, connect the remaining end of the telephone interface cable into the open handset port on the desk phone.Disconnect the handset coil cord from the base of the desk phone and re-connect it to the telephone interface cable junction box.Connect one end of the telephone interface cable to the back of the base.In this configuration, press both the headset button on your desk phone and the call control button on the headset to answer or end calls. NOTE Use this setup if you are not using the HL10 lifter or EHS cable. Connect the other end of the telephone interface cable into the dedicated headset port on the desk phone.NOTE Base configuration settings Desk phone Setting (on bottom of base) Most phones A Cisco phones D Cisco phones with EHS cable AĬhoose a desk phone setup A, B, C or D and connect cables.Ī Desk phone with a dedicated headset port Enables remote call control with your headset. HL10 lifter Automatically lifts handset and returns it to the cradle.Electronic hookswitch cable (EHS cable) Electronically and automatically answers/ends a desk phone call.Plantronics products using the new enhanced version of DECT that includes these security improvements are marked on the base with the DECT Forum security logo.Ģ Microsoft Teams button (Teams model only, app required) Plantronics DECT products have been tested against and passed the DECT Forum security certification requirements and consequently have been granted the ‘DECT Forum security’ logo certification. Plantronics DECT products are now secure against all the known vulnerabilities that were highlighted by the public announcements of the Chaos Communication Congress in 2009. These improvements cover registration, authentication, authorization, and encryption procedures. Plantronics DECT-based products now fully incorporate the latest recommendations on Enhanced Security from the DECT Forum and ETSI. Plantronics is a member of the DECT Forum and has fully adopted its recommendations for enhancements to security within all DECT products. Use of this DECT 6.0 product in unauthorized countries is a violation of law, may disrupt telecommunications networks and devices, and can subject you to fines and penalties by regulatory agencies. DECT 6.0 devices are generally authorized for use in the S/Canada/Mexico. The enclosed DECT 6.0 wireless product uses restricted wireless radio frequencies which vary by country. DECT products should never be used outside the region in which they were originally purchased and intended to be used.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |